1. Computer Network is for aiding ‘Data Communication’, i.e., sending and receiving of data between terminals situated at different places.
2. There are 3 types of ‘Transmission Channels’, namely, Simplex, Half Duplex and Full Duplex Channels.
3. A(sender) à B(receiver) : is the simplex channel, where data transmission is in one way direction. Here the receiver can not send any communication back to the sender via the same channel.
4. Half Duplex channel – where the transmission of data is from both ends, but at any particular time only one is happening, either incoming or outgoing transmission. The diagram bellow shows a gap in space between the sender and receiver messages, to denote the gap in time where at one time only one message (either form the sender or from the receiver) will get transmitted.
2. There are 3 types of ‘Transmission Channels’, namely, Simplex, Half Duplex and Full Duplex Channels.
3. A(sender) à B(receiver) : is the simplex channel, where data transmission is in one way direction. Here the receiver can not send any communication back to the sender via the same channel.
4. Half Duplex channel – where the transmission of data is from both ends, but at any particular time only one is happening, either incoming or outgoing transmission. The diagram bellow shows a gap in space between the sender and receiver messages, to denote the gap in time where at one time only one message (either form the sender or from the receiver) will get transmitted.
5. Full Duplex channel, is where the data gets transmitted in both directions at the same time, i.e., there is no time lag or delay in communication.
6. There are 4 main types of ‘Network Topology’, namely, Mesh, Star, Ring and Bus Network.
7. Topology means the arrangement of various components of a network (such as server/hubs/nodes/links/information flow channels etc.), and depicts the structure of a network.
8. The following diagrammatic representation is of ‘Mesh Networking’ – the small rectangular boxes are ‘Nodes’.
In mesh network, each node is independent, and is used for high traffic transmission through multiple available routes. This is a fully connected network, where each node in the network to the other.
The bus networks are the simplest of networks, but it has a critical drawback. It can transmit from one node at a time, because of the single line of communication.
12. Node is a connection point where data transmission originates or ends.
7. Topology means the arrangement of various components of a network (such as server/hubs/nodes/links/information flow channels etc.), and depicts the structure of a network.
8. The following diagrammatic representation is of ‘Mesh Networking’ – the small rectangular boxes are ‘Nodes’.
In mesh network, each node is independent, and is used for high traffic transmission through multiple available routes. This is a fully connected network, where each node in the network to the other.
As you can see in the diagram, each node is connect to the other four,
which is why this type of network is highly reliable for data
transmission as there are more than one route for transmission.
Plus is a particular route fails – then the transmission can automatically switch to other available routes and the transmission will be successfully completed.
Plus is a particular route fails – then the transmission can automatically switch to other available routes and the transmission will be successfully completed.
9. In ‘Star Network’, there is a ‘Cental Node’, which is also called the ‘Hub’. For your easy understanding, think of hub as a Server and the other nodes attached to it are the client nodes.
The
communication between the clients takes place through the server. A
client (sender) send information to the hub, the hub then transmits the
information to the client (receiver) for whom the information was meant
to be transmitted.
In this type of network, if the transmission line between the hub and a node fails, then that node will become isolated from the network.
And if the central node fails, then the whole network fails!
10. In ‘Ring Network’ topology, each node is connected to two other nodes only.
The data flow is usually one way in a ring network, and hence if any line/node fails then the entire network crumbles.
11. ‘Bus Network is the type of topology in which the nodes are connected by a single communication line. This single communication line is called a bus.
The
communication between the clients takes place through the server. A
client (sender) send information to the hub, the hub then transmits the
information to the client (receiver) for whom the information was meant
to be transmitted.In this type of network, if the transmission line between the hub and a node fails, then that node will become isolated from the network.
And if the central node fails, then the whole network fails!
10. In ‘Ring Network’ topology, each node is connected to two other nodes only.
The data flow is usually one way in a ring network, and hence if any line/node fails then the entire network crumbles.
11. ‘Bus Network is the type of topology in which the nodes are connected by a single communication line. This single communication line is called a bus.
The bus networks are the simplest of networks, but it has a critical drawback. It can transmit from one node at a time, because of the single line of communication.
12. Node is a connection point where data transmission originates or ends.
13. Terminal is a computer network means a computer
equipment, it could be anything – a computer, an ATM machine, the PNR
and Train time requesting machines at railway stations.
14. Dumb Terminals are those terminals which cannot do any processing or storage of data. It is simply an input/output device wired into another computer. It takes the input, transmits the data to the computer (computers can process!) to which it is connected and then displays the output.
Examples: Like PNR status checking booth at Railway stations. They have a Cathode Ray Tube (Screen), a Keyboard, or screen with touch input and gives the output on the screen.
15. Intelligent Terminals is the kind of terminal which can do its own processing…which would mean it is fitted with a processor and has memory (storage) capacity and thus is actually a computer (but not the kind which looks like our PC!)
16. Smart Terminals have processing capacities and memory too, but lesser than intelligent terminals.
So the hierarchy would be (lowest to highest ) – Dumb – Smart – Intelligent Terminals.
There you go guys computer network and its absolute basics – hope this was helpful!
14. Dumb Terminals are those terminals which cannot do any processing or storage of data. It is simply an input/output device wired into another computer. It takes the input, transmits the data to the computer (computers can process!) to which it is connected and then displays the output.
Examples: Like PNR status checking booth at Railway stations. They have a Cathode Ray Tube (Screen), a Keyboard, or screen with touch input and gives the output on the screen.
15. Intelligent Terminals is the kind of terminal which can do its own processing…which would mean it is fitted with a processor and has memory (storage) capacity and thus is actually a computer (but not the kind which looks like our PC!)
16. Smart Terminals have processing capacities and memory too, but lesser than intelligent terminals.
So the hierarchy would be (lowest to highest ) – Dumb – Smart – Intelligent Terminals.
There you go guys computer network and its absolute basics – hope this was helpful!
No comments:
Post a Comment